Design of Experiments (Doe) on Suspension Test Equipment of One Part Of A Vehicle Wheel Using The Taguchi Method
DOI:
https://doi.org/10.31963/intek.v10i2.4581Keywords:
optimization, simulation, vibration, suspension, pneumatic actuatorAbstract
Suspension is the most important thing that must be taken into account because it greatly affects driving comfort on the road. The working mechanism of the suspension consisting of spiral springs and shock absorbers is loaded vertically from the weight of the body, driver, and passengers. The uneven shape of the road surface in the form of potholes or bumps will greatly affect the comfort of the driver. This study aims to determine the effect of suspension work and the optimal value of vibration that occurs on one of the wheels of the vehicle against vertical dynamic loads. The method used in this study uses the Taguchi method which is used to determine the optimum dynamic load conditions against vibration in the suspension system.  The characteristics used in this method are "Smaller is better". Several variables such as bump height, tire pressure on the wheels, as well as vehicle body weight and passenger weight are necessary factors to calculate optimal dynamic load conditions against vibration in the suspension. Based on the results of the optimum value conditions obtained, namely the height of the mound of 5 cm, tire pressure of 32 Psi, load of 84 kg, and dynamic load of 71 kg. From the results of the contribution rate to the ANOVA obtained, factor A (bump height) and factor D (dynamic load) are significant factors while factor B (tire pressure) and factor C (load load) are insignificant factors. Under optimal conditions, there was a decrease in suspension vibration value by 49.65%.References
Leo Santoso, A. A. R. Analisis Dampak Beban Overloading Kendaraan pada Struktur Rigid Pavement Terhadap Umur Rencana Perkerasan. Teknik Sipil, 19, 8,(2012).
Kabra, Ashish, Parametric Optimization & Modeling for Surface Roughness , Feed and Radial Force of EN-19 / ANSI-4140 Steel in CNC Turning Using Taguchi and Regression Analysis Method (20130,(2013).
Listiyono, Dkk, 2020. Optimalisasi Tekanan Shock Absorber Dan Tekanan Pegas Coil Terhadap Getaran Mobil. Jurnal Energi Dan Teknologi Manufaktur. Vol. 03, No. 01, 05 – 10
Gunawan. Optimasi Kinerja Suspensi Untuk MeningkatkanKenyamanan Dengan Variasi Tekanan Ban Dan Berat Pada Kendaraan Innova 2000 Cc. Jurnal Keselamatan Transportasi Jalan.vol. 2338-4247 (2019).
S. Simon Kaka, Himran, I. Renreng, and O. Sutresman, “Shock absorber and spring contribution reduces vertical vehicle loads that burden the road structure,†ARPN J. Eng. Appl. Sci., vol. 13, no. 22, pp. 8686–8692, (2018).
Munaf F. Badr , L. Asst. Prof.,Jaliel,E.A.K. . Position Control of the Pneumatic Actuator Employing ON/OFF Solenoids Valve. International Journal of Mechanical & Mechatronics Engineering IJMME-IJENS, Vol.17 No.02, 9.(2016).
Nurcahyanto, E. Penggunan Algoritma GenetikUntuk Perancangan Sistem Suspensi OptimalPada Model Kendaraan Seperempat. 10.(2004).
Bangsing, N. Pengujian Prototip Suspensi Aktif Tegar (Robust) Model Seperempat Kendaraan. PROC. ITB sains & Tek., Vol. 36 A, 1., 83-95.(2004).
Edge, E. Helical Compression Spring Design Equation and Calculator. Became An Engineers Edge Contributor.(2017).
Trabelsi, P.H.A.Y., Louati,J.,and Haddar,M., Interval computation and constraint propagation for the optimal.(2015).
Anggoro Aristanto1, S., S.T, M.T2, DARJAT, S.T, M.T2. Aplikasi Fuzzy Logic Control Pada Sistem Suspensi Semi-Aktif Model Kendaraan Seperampat. Universitas Diponegoro,(2012).
Rehnberg, A. Vehicle dynamic analysis ofwheel loaders with suspended axles. TRITA-AVE, 15.(2008)
S. Ka’ka, D. Kambuno, and A. Tangkemanda, “Damping transformation modeling on wheel suspension using pneumatic cylinder thrust force as a substitute for vehicle weight,†J. Vibroengineering, pp. 363–376, 2022, doi: 10.21595/jve.2022.22619.
Soejanto, I. 2009. Desain Eksperimen dengan Metode Taguchi. Yogyakarta: Graha Ilmu.
Krishnaiah, K., and P. SHAHABUDEEN. 2012. Applied Design of Experiments and Taguchi Methods. https://books.google.com/books?id=hju9JYVhfV8C&pgis=1.
Selvaraj, D. Philip. 2018. “Optimization of Surface Roughness of Duplex Stainless Steel in Dry Turning Operation Using Taguchi Technique.†Materials Physics and Mechanics 40(1): 63–70.
C. G. Simon, F. A. Hardinsi, and F. Paliling, “Comparison of the Effect of Variable Helix Angle Geometry Tools on CNC Vertical Milling Machines on Chatter using a microcontroller Based on SLD,†vol. 10, no. 1, pp. 26–32, 2023. DOI: http://dx.doi.org/10.31963/intek.v10i1.4265
Geraldi Simon, C., Andre Hardinsi, F., Suluh, S., Paliling, F., Sampelolo, R., Widyianto, A. (2023). Enhancing vehicle wheel suspension test equipment through Taguchi method for optimization. Eastern-European Journal of Enterprise Technologies, 5 (1 (125)), 15–27. doi: https://doi.org/10.15587/1729-4061.2023.288476
S. Ka’ka, “The Pneumatic Actuators As Vertical Dynamic Load Simulators On Medium Weighted Wheel Suspension Mechanism,†J. Phys., vol. 1, no. 2017, p. 10, 2018.
Festo Andre Hardinsi., Oyong Novareza., Achmad As’ad Sonief. Optimization Of Variable Helix Anglse Parameters In Cnc Milling Of Chatter And Surface Roughnes Using Taguchi Method. Journal Of Engineering And Management In Industrial System Vol. 9 No. 1 (2021)
