Sistem Kendali Hidrogen Pada HCl Burner Menggunakan Controller Yokogawa
DOI:
https://doi.org/10.31963/elekterika.v20i1.4181Keywords:
HCl burner, controller, control valve, flow transmitter, pressure transmitterAbstract
The hydrogen control system is a hydrogen control system in the HCl manufacturing process. This control is needed to control the presence of hydrogen over capacity or low capacity in the HCl burner, resulting in product failure. Hydrogen is one of the first steps for making HCl, which needs to be considered for its parameters, consisting of a control valve, flow transmitter, and pressure transmitter. In this study, a controller can be operated to adjust the hydrogen control valve line opening on the HCl burner. Then to find out the set point value of hydrogen entering the HCl burner, 2 transmitters measure flow and pressure. Furthermore, the signal measured by the transmitter will provide feedback so that the flow and pressure values appear on the controller. To ensure that the parameter data has been observed by comparison between the data on the system and the actual data in the field. From the observational data of this control system, the need for hydrogen for the initial stage of HCl production can be carried out within 1 hour with the control valve opening parameter of 34%, so that by opening the control valve it is known that the flow transmitter indication is 34 kg/hour and the transmitter pressure is 9kPa, so from flow and pressure indications can be used for later stages of the HCl manufacturing process.References
K. Kevin, V. L. Aria, R. Handogo, and J. P. Sutikno, “Pra Desain Pabrik Asam Klorida dari Elektrolisis Garam Industri,†J. Tek. ITS, vol. 10, no. 2, pp. 139–144, 2021, doi: 10.12962/j23373539.v10i2.68949.
S. YULIAN, “PABRIK HCl DARI GARAM NONELECTROLYSIS,†2013, [Online]. Available: http://eprints.upnjatim.ac.id/5855%0Ahttp://eprints.upnjatim.ac.id/5855/1/file1.pdf
S. Rijal J, “Prototype Hydrogen Fuel Generator Dry Cell Type (Produksi Gas Hidrogen Ditinjau dari Variasi Konsentrasi Elektrolit Asam Klorida dengan Suplai Tegangan Listrik),†vol. 2, no. l, pp. 5–22, 2015, [Online]. Available: http://eprints.polsri.ac.id/id/eprint/2023
L. Hamdani, “Pra Rancangan Pabrik Klorin Dioksida dengan Proses Senior Vibe Preseident (SVP) Kapasitas 30.000 Ton/Tahun,†pp. 1–131, 2019.
P. Elda Swastika, F. Hardheyanti, R. Prasetyowati, A. Ariswan, and W. Warsono, “Pengaruh Konsentrasi HCl terhadap Mikrostruktur dan Sifat Kemagnetan Nanopartikel Fe3O4 yang Disintesis dari Pasir Besi Pantai Glagah Kulonprogo,†J. Sains Dasar, vol. 10, no. 1, pp. 24–29, 2021, doi: 10.21831/jsd.v10i1.39141.
H. L. Gratianus, P. Pangaribuan, and J. Halomoan, “Perancangan Kendali Valve Dan Pemantauan Pendistribusian Cairan Pada Tangki,†Ijurnal Tek. elektro Univ. Telkom SSN 2355-9365, vol. Vol. 2. No, pp. 1–13, 2015.
D. A. Fenanda, I. W. Farid, and C. W. Priananda, “Kontrol Flow Gas pada Pengembangan Sistem Distribusi Gas Rumah Tangga Menggunakan PLC dan Metode Fuzzy Logic,†J. Tek. ITS, vol. 10, no. 2, pp. 191–196, 2021, doi: 10.12962/j23373539.v10i2.68298.
A. . Fallis, “Sistem Pengendalian dan Control,†J. Chem. Inf. Model., vol. 53, no. 9, pp. 1689–1699, 2013.
R. Damayanti, P. Santosa, and B. Santoso, “Penentuan Ukuran Control Valve Pada Unit Pengolahan Air Bebas Mineral Iradiator Gamma PRFN,†Prima, vol. 12, no. 1, pp. 9–19, 2015.
D. Afrizal and S. O. Kunang, “Rancang Bangun Sistem Kendali Pneumatic Pump Dalam Proses Kalibrasi Pressure Transmitter,†Bina Darma Conf. Eng. Sci., vol. 4, no. 1, pp. 121–132, 2022, [Online]. Available: http://conference.binadarma.ac.id/index.php/
